Thin-Film-Transistor LCD Module
Display Resolution：Display Resolution
Active Area：154.08 (H) x 85.92 (V)
Outline Dimension：170.08(W) x 103.92(H) x5.525 (D)
Thin-Film-Transistor LCD Module
7 inch car DVD LCD screen
Description of 7 inch car DVD LCD screen XTPW70NP01-07
154.08 (H) x 85.92 (V)
170.08(W) x 103.92(H) x5.525 (D)
Gray scale inversion Direction ion
HX8264*1 HX8664*1 or Compatible
1.General Description and Features of 7 inch car DVD LCD screen XTPW70NP01-07
7" TFT LCD XTPW70NP01-07 can be used for a car DVD LCD screen, displaying video, controlling PTZ. 7 inch car DVD LCD screen XTPW70NP01-07 is easy to operation, and its portability makes it simple for the CCTV technician to install and maintain CCTV system, improving work efficiency and get the labor cost down.
2 Input Terminal Pin Assignment of 7 inch car DVD LCD screen XTPW70NP01-07
Touch Panel Vendor ID:
Address: 0xA8 Data:0X03
Firmware version number:
Address: 0xA6 Data:0x01
3 Reliability Condition for LCD 7 inch car DVD LCD screen XTPW70NP01-07
No change on display and in operation under the following test condition.
Condition: Unless otherwise specified, tests will be conducted under the following condition.
Temperature: 20±5°C Humidity: 65±5%RH
Tests will be not conducted under functioning state.
High Temperature Operating
70°C±2°C, 240hrs (Operation state)
Low Temperature Operating
-20°C±2°C, 240hrs (Operation state)
High Temperature Storage
Low Temperature Storage
High Temperature and High
Humidity Operation Test
60°C±2°C, 90%, 240hrs
Total fixed amplitude: 1.5mm
Vibration Frequency: 10~55Hz
One cycle 60 seconds to 3 direction of X, Y, Z each 15 minutes.
To be measured after dropping from 60cm high on the concrete surface in packing state.
1. No dew condensation to be observed.
2. The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber.
3. Vibration test will be conducted to the product itself without putting I in a container.
3 Dimensional outlines of 7 inch car DVD LCD screen XTPW70NP01-07
Inspection performed under the following conditions is recommended.
Temperature : 25±5℃
Humidity : 65%±10%RH
Viewing Angle : Normal viewing Angle.
Illumination: Single fluorescent lamp (300 to 700Lux)
Zone A : Effective Viewing Area(Character or Digit can be seen)
Zone B : Viewing Area except Zone A
Zone C : Outside (Zone A+Zone B) which can not be seen after assembly by customer .)
Note:As a general rule ,visual defects in Zone C can be ignored when it doesn’t effect product functionor appearance after assembly by customer.
According to GB/T 2828-2003 ; , normal inspection, Class Ⅱ
LCD: Liquid Crystal Display , TP: Touch Panel , LCM: Liquid Crystal Module
Items to be inspected
Classification of defects
1)No display, Open or miss line
Overall outline dimension beyond the drawing is not allowed
Color unevenness, refer to limited sample
Good soldering , Peeling off is not allowed.
Black/White spot/line, scratch, crack, etc.
(1) The edge of LCD broken
(2)LCD corner broken
(3) LCD crack
Line defect (LCD/TP
/Polarizer black/white line, scratch, stain)
According to IPC-A-610C class Ⅱ standard . Function defect and missing part are major defect ,the others are minor defect.